DESIGN AND CONSTRUCTION OF A GSM-BASED ENERGY METER


DESIGN AND CONSTRUCTION OF A GSM-BASED ENERGY METER  

ABSTRACT

Wireless automation in the generation, transmission and distribution of electricity and billing has come of age. Traditional metering methods for retrieving the energy data of consumers is not convenient. The present system of energy billing is error prone, time, resource and labour consuming. The problem worsens when consumers try to bypass meter units, thereby pay less than what is actually consumed or the case of overbilling by the Electricity Company as the case in many Nigerian houses.

This paper presents the design and implementation of a GSM based remote operation of an energy meter which proffers the solution to power theft, consumption control, auto billing and payment, data logging and labour reduction in power distribution and management

The objective of this project is to facilitate energy consumption measurement and its corresponding billing scheme.

The materials and method deployed herein is the use of a microcontroller unit that continually monitors the meter interfaced with a GSM MODEM with a dedicated SIM for remote operations. The method used to carry out this project is the principle of serial communication in collaboration with embedded systems. The meter provides corresponding billing Information on a LCD screen.

TABLE OF CONTENTS

COVER PAGE i

TITLE PAGE ii

DECLARATION iii

CERTIFICATION iv

DEDICATION v

ACKNOWLEDGEMENT vi

ABSTRACT vii

LIST OF FIGURES viii

CHAPTER ONE

INTRODUCTION 1

i. BACKGROUND 1

ii. PROBLEM STATEMENT 2

iii. OBJECTIVES 2

iv. SIGNIFICANCE 3

v. SCOPE 3

CHAPTER TWO

LITERATURE REVIEW 5

2.1 HISTORY OF ELECTRIC ENERGY METERS 5

DIRECT CURRENT (DC)5

ALTERNATING CURRENT (AC)6

UNITS OF MEASUREMENT6

TYPES OF METERS7

ELECTROMECHANICAL METERS7

ELECTRONIC METERS9

SOLID STATE DESIGN9

TAMPERING AND SECURITY IN ENERGY METERS14

POWER LINE RELATED INTELLIGENT METERING (PRIME)15

INTRODUCTION TO GSM NETWORK15

MESSAGING OVER GSM NETWORK16

GSM NETWORK STRUCTURE17

CHAPTER THREE

DESIGN AND CONSTRUCTION PROCEDURE 18

INTRODUCTION18

SYSTEM DESCRIPTION18

SYSTEM BLOCK DIAGRAM19

SECTION A. DESIGN PROCEDURE 19

HARDWARE DESIGN19

CIRCIUT ANALYSIS19

REGULATED POWER SUPPLLY20

BRIDGE RECTIFIER20

FILTERING CAPACITORS21

ZENER REGULATOR DESIGN23

TRANSISTOR TIP 4125

LM317T VOLTAGE REGULATOR25

RATED DC OUTPUT27

CURRENT SENSING DESIGN27

RELAY SWITCHING32

THE MICROCONTROLLER UNIT32

CRYSTAL OSCILLATOR DESIGN36

LED INDICATORS37

THE BUZZER39

INTERFACING THE LCD WITH THE MICROCONTROLLER39

INTERFACING THE GSM MODEM WITH MICROCONTROLLER41

THE MAX 232 IC43

SOFTWARE DESIGN46

SECTION B: CONSTRUCTION PROCEDURE 49

CIRCIUT DESIGN USING PRINTED CIRCIUT BOARD (PCB)49

CASING AND PACKAGING51

CHAPTER FOUR

PERFORMANCE AND COST EVALUATION 55

PERFORMANCE EVALUATION55

DESIGN SIMULATION55

PERFORMANCE TEST55

COST EVALUATION59

CHAPTER FIVE

CONCLUSIONS 63

SUMMARY63

CONCLUSION63

RECOMMENDATIONS64

REFERNCES 65

APPENDICE 68

LIST OF TABLES

TABLE 3.1 PIC18F2550 FEATURES 33

TABLE 3.2 VALUE OF CAPACITOR USED 36

TABLE 3.3 LCD PIN FUNCTIONS 40

TABLE 3.4 AT COMMAND AND RESPONSE 42

TABLE 4.1 SMS COMMAND AND FUNCTIONS 59

TABLE 4.1 COST EVALUATION 60

LIST OF FIGURES

FIG 2.1 A 3Ø electromechanical induction meter, metering 100 A 240/415 V supply 7

FIG 2.2 A digital meter 8

FIG 2.3 A solid state energy meter design 9

FIG 2.4 PRIME core structure 15

FIG 2.5 GSM network structure 17

FIG 3.1 SYSTEM BLOCK DIAGRAM 19

FIG. 3.2 POWER RECTIFICATION CIRCUIT 20

FIG.3.3 ZENER REGULATOR CIRCUIT 24

FIG. 3.4 TIP 41 BUFFER TRANSISTOR 25

FIG. 3.5 BLOCK DIAGRAM OF LM317T 26

FIG. 3.6 LM 317T IN CIRCUIT REGULATION 26

FIG. 3.7 FUNCTIONAL BLOCK DIAGRAM OF ACS755-100CB 28

FIG. 3.8 OUTPUT VOLTAGE VS SENSED CURRENT OF ACS755 AT 5.0 V POWER

SUPPLY AND VARYING TEMPERATURE 29

FIG. 3.9 CURRENT SENSOR CIRCUITRY 30

FIG. 3.10 THE RELAY CIRCUIT 31

FIG. 3.11 THE PIC18F2550 PIN CONFIGURATION 33

FIG.3.12 BLOCK DIAGRAM OF PIC18F2550 35

FIG.3.13 CRYSTAL OSCILLATOR CIRCUIT 37

FIG. 3.14 LED SCHEMATIC SYMBOL AND I-V CHARACTERISTICS CURVES SHOWING THE DIFFERENT COLOURS AVAILABLE 38

FIG. 3.15 SERIES LED CONNECTION 38

FIG.3.16 LCD 40

FIG. 3.17 SMART GSM MODEM 41

FIG.3.18 INSERTING/REMOVING THE SIM CARD INTO THE MODEM 42

FIG.3.19 TYPICAL OPERATING CIRCUIT OF THE MAX 232 IC 44

FIG.3.20 THE MAX 232 INTERFACED WITH DB9 CONNECTOR TO MODEM 44

FIG.3.21 CIRCUIT DIAGRAM OF GSM BASED ENERGY METER 45

FIG. 3.23 FLOWCHART OF PROGRAMME 48

FIG. 3.24 PCB LAYOUT 50

FIG. 3.25 PLY WOOD SURFACE MOUNTING 51

FIG. 3.26 TOP VIEW OF CASING 52

FIG. 3.27 INSIDE VIEW OF PVC CASING 52

LIST OF PLATES

PLATE 3.1 SOLDERED COMPONENTS MOUNTED ON PCB 50

PLATE 3.2 SET UP OF GSM BASED ENERGY METER 53

PLATE 3.3 CASING OF METER UNIT SHOWING THE COMPONENTS AND GSM

MODEM 54

PLATE 4.1 THE METER UNIT INDICATING MODEM IS CONNECTED 55

PLATE 4.2 THE METER UNIT WITH LOAD CONNECTED 55

PLATE 4.3 LCD SCREEN INDICATING ENERGY CONSUMPTION DETAILS 56

PLATE 4.4 LCD SCREEN INDICATING THE METER CHECKING FOR SMS 56

PLATE 4.5 SCREEN SHOT OF SMS RECEIVED FROM THE METER UNIT 57

CHAPTER ONE

INTRODUCTION

BACKGROUND

Today, humanity can be classified as living in a “machine society” where technological tools are predominantly at different levels, interfacing in the day–to-day activity of man.

These livelihood activities constitute and deliver economic, social and political benefits and potential risks to the survivability of nations –especially developing nations like ours.

Electricity has become one of the basic requirements of human civilization, being widely deployed for domestic, industrial and agricultural purposes. In spite of the very well developed sources of electricity, there are a number of problems with distribution, metering, billing and control of consumption. Electricity is one of the vital requirements for sustainment of comforts of life and so it should be used very judiciously for its proper utilization [1]. But in our country we have lot of localities where we have surplus supply for the electricity while many areas do not even have access to it. Our policies of its distribution are also partially responsible for this because we are still not able to correctly estimate our exact requirements and still power theft is prevailing [1].

On the other hand consumers are also not satisfied with the services of power companies, most of the time they have complaints regarding statistical errors in their monthly bills.

Thus this project presents an innovation towards the minimization of technical errors and reduction in human dependency at the same time. With the help of this project the monthly energy consumption of a consumer will be received from a remote location directly. In this way human effort needed to record the meter readings which are till now recorded by visiting

15

every home individually is reduced. This results in considerable loss of human hours and also provides considerable details regarding the average consumption of a locality so that power supply can be made according to these data. This will help the officials in deciding the specifications of transformers and other instruments required in power transmission and distribution.

This idea is economically efficient as well because the meter reading can be gotten at a very low cost. The implementation is done in such a way that a SMS is delivered to the GSM MODEM whose reading is to be noted and then that meter replies to the server in the SMS format and it is known that SMS costs are very low.

The GSM AMR takes the advantage of available GSM infrastructure nationwide coverage and the Short Messaging System (SMS) cell broadcasting feature to request and retrieve individual houses and building power consumption reading back to the energy provider wirelessly.

PROBLEM STATEMENT

In Conventional metering system to measure electricity consumption the energy provider company hire persons to visit each house and record meter reading manually which is used for billing, the bill then sent to consumer by post or hand delivery, this is not only sluggish but laborious, with the company having no control over these meters. There is a stark amount of revenue loss being incurred by our country due to energy theft which is a serious problem, people try to manipulate meter reading by adopting various corrupt practices such as current reversal, partial earth fault condition, bypass meter, magnetic interference etc. [2]. With the aid of this project a definite solution is proffered which allows power companies to have total control over energy meters and have real time information of same from a remote location with little human effort and at reduced cost as compared to conventional methods.

16

OBJECTIVE

The purpose of this project is the remote monitoring and control of the domestic energy meter; its aims includes: to design a circuit which continuously monitors the meter reading and sends message to electricity company, programming of the GSM MODEM with AT (Attention) command sequence, interfacing the programmable chip with the personal computer, interfacing the programmable chip with the energy meter, interfacing of GSM MODEM with the programmable chip, sending messages from the remote phone to control device.

SIGNIFICANCE

The significance of these project benefits the Consumers of electric service and the electric services company as it provides precise consumption information, clear and accurate billing, automatic outage information and faster recovery, better and faster customer service, smart automated processes instead of manual work, accurate information from the network load to optimise maintenance and investments, detection of tampering of meters, demand and distribution management, better company credibility, consumer meter reading which eliminates cost and inadequacies of manual reading, observation and control of energy consumption and production, this is useful for planning and power allocation purposes.

The project provides learning’s on the following advancements in terms of theory practice: GSM modem interfacing to Microcontroller, PC interfacing with GSM modem, energy meter interfacing to Microcontroller, embedded C programming, PCB (printed circuit board) design, LCD interfacing to Microcontroller.

SCOPE

The scope of this project is to design and construct GSM based a one phase two wire energy meter with voltage rating of 220V, current of 25 -100A operating at 50Hz and interfaced

17

with a microcontroller unit and GSM module with a LCD with the wireless communication features over SMS. Within the scope of this project, the prototype model is equipped with a dedicated SIM (Subscriber Identification Module).

.

DESIGN AND CONSTRUCTION OF A GSM-BASED ENERGY METER



TYPE IN YOUR TOPIC AND CLICK SEARCH.






RESEARCHWAP.NET
Researchwap.net is an online repository for free project topics and research materials, articles and custom writing of research works. We’re an online resource centre that provides a vast database for students to access numerous research project topics and materials. Researchwap.net guides and assist Postgraduate, Undergraduate and Final Year Students with well researched and quality project topics, topic ideas, research guides and project materials. We’re reliable and trustworthy, and we really understand what is called “time factor”, that is why we’ve simplified the process so that students can get their research projects ready on time. Our platform provides more educational services, such as hiring a writer, research analysis, and software for computer science research and we also seriously adhere to a timely delivery.

TESTIMONIES FROM OUR CLIENTS


Please feel free to carefully review some written and captured responses from our satisfied clients.

  • "Exceptionally outstanding. Highly recommend for all who wish to have effective and excellent project defence. Easily Accessable, Affordable, Effective and effective."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "I saw this website on facebook page and I did not even bother since I was in a hurry to complete my project. But I am totally amazed that when I visited the website and saw the topic I was looking for and I decided to give a try and now I have received it within an hour after ordering the material. Am grateful guys!"

    Hilary Yusuf, United States International University Africa, Nairobi, Kenya.
  • "Researchwap.net is a website I recommend to all student and researchers within and outside the country. The web owners are doing great job and I appreciate them for that. Once again, thank you very much "researchwap.net" and God bless you and your business! ."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "Great User Experience, Nice flows and Superb functionalities.The app is indeed a great tech innovation for greasing the wheels of final year, research and other pedagogical related project works. A trial would definitely convince you."

    Lamilare Valentine, Kwame Nkrumah University, Kumasi, Ghana.
  • "I love what you guys are doing, your material guided me well through my research. Thank you for helping me achieve academic success."

    Sampson, University of Nigeria, Nsukka.
  • "researchwap.com is God-sent! I got good grades in my seminar and project with the help of your service, thank you soooooo much."

    Cynthia, Akwa Ibom State University .
  • "Sorry, it was in my spam folder all along, I should have looked it up properly first. Please keep up the good work, your team is quite commited. Am grateful...I will certainly refer my friends too."

    Elizabeth, Obafemi Awolowo University
  • "Am happy the defense went well, thanks to your articles. I may not be able to express how grateful I am for all your assistance, but on my honour, I owe you guys a good number of referrals. Thank you once again."

    Ali Olanrewaju, Lagos State University.
  • "My Dear Researchwap, initially I never believed one can actually do honest business transactions with Nigerians online until i stumbled into your website. You have broken a new legacy of record as far as am concerned. Keep up the good work!"

    Willie Ekereobong, University of Port Harcourt.
  • "WOW, SO IT'S TRUE??!! I can't believe I got this quality work for just 3k...I thought it was scam ooo. I wouldn't mind if it goes for over 5k, its worth it. Thank you!"

    Theressa, Igbinedion University.
  • "I did not see my project topic on your website so I decided to call your customer care number, the attention I got was epic! I got help from the beginning to the end of my project in just 3 days, they even taught me how to defend my project and I got a 'B' at the end. Thank you so much researchwap.com, infact, I owe my graduating well today to you guys...."

    Joseph, Abia state Polytechnic.
  • "My friend told me about ResearchWap website, I doubted her until I saw her receive her full project in less than 15 miniutes, I tried mine too and got it same, right now, am telling everyone in my school about researchwap.com, no one has to suffer any more writing their project. Thank you for making life easy for me and my fellow students... Keep up the good work"

    Christiana, Landmark University .
  • "I wish I knew you guys when I wrote my first degree project, it took so much time and effort then. Now, with just a click of a button, I got my complete project in less than 15 minutes. You guys are too amazing!."

    Musa, Federal University of Technology Minna
  • "I was scared at first when I saw your website but I decided to risk my last 3k and surprisingly I got my complete project in my email box instantly. This is so nice!!!."

    Ali Obafemi, Ibrahim Badamasi Babangida University, Niger State.
  • To contribute to our success story, send us a feedback or please kindly call 2348037664978.
    Then your comment and contact will be published here also with your consent.

    Thank you for choosing researchwap.com.